Custom Cabinetry in Sarasota, FL

Custom cabinets in Sarasota, room by room

Kitchens take most of our bench time, but the same joinery and finishing go into every room of a house.

Kitchens

Perimeter runs, islands, pantry walls and appliance garages make up the bulk of our work. If you are planning a full renovation with layout changes, start with our page on kitchen remodeling in Sarasota, where design, cabinetry and installation come together with the licensed trades your project needs.

Baths and powder rooms

Vanities, linen towers and medicine-cabinet walls face more steam than any kitchen. Our bathroom remodeling work starts from the cabinetry and brings in a licensed plumber and tile setters for the rest.

Living spaces, closets and offices

Bookcases, TV walls, desks, laundry rooms and closets are cabinetry too, only arranged differently. See custom built-ins for the rooms beyond the kitchen and bath.

Which cabinetry service fits your project?

Most people arrive here with one of five problems. Each has its own page with the detail that matters for that job:

• New cabinets for a kitchen. Custom kitchen cabinets covers door styles, inset versus overlay, coastal finishes and how we size each run to the inch.
• Cabinets already ordered, but nobody to set them. Kitchen cabinet installation explains how we scribe, level and trim cabinets, including ones a designer or another supplier ordered.
• Worry about swelling and sagging in the humidity. Solid wood cabinets explains why pressed-board boxes never leave our shop and how real joinery holds up here.
• A clean, contemporary look. Modern European cabinets covers frameless boxes, flat panels, high gloss and handleless doors.
• Cabinets that mostly work but need fixing. Cabinet repair handles broken drawers, tired hinges, soft-close upgrades and modifications for new appliances.

If your boxes are sound and only the faces look dated, cabinet refacing may cost less than a new set.

Signs a Sarasota house has outgrown its cabinets

Local warning signs: a sink-base floor gone soft from a slow drip; drawer bottoms dropping out of stapled 1990s-2000s builder boxes; doors that never close square in 1950s-60s block homes; and cabinets that stood in Ian, Helene or Milton floodwater, which pressed board rarely survives. Storm-damaged kitchen repair covers that last case.

What woods and box materials go into a custom cabinet?

Materials decide how a cabinet behaves in its fifteenth humid August, not only how it looks on install day.

For a deeper look at box construction and humidity, read our solid wood cabinets page.

Design decisions we settle on paper first

Drawings and a rendered model come before any cutting. That stage is where most of the important choices get made, and where changes cost nothing but a redraw.

• Door mounting. Inset doors sit inside the frame for a furniture look; overlay doors cover it and forgive small seasonal movement.
• Framed or frameless. Face-frame boxes are our traditional standard; frameless boxes give full access for a modern kitchen.
• Appliance specs. We build openings from the manufacturer's installation sheets, so the refrigerator, range and dishwasher fit as drawn.
• Ceiling height and crown. Tall ceilings, common in newer homes east of I-75, often call for stacked uppers or a second tier of glass doors.
• Interior fittings. Roll-outs, tray dividers, spice pull-outs, trash bins and charging drawers are planned into the box, not added later.

How does a custom cabinet maker in Sarasota run a project?

1. 1

   Conversation and site measure

   We visit, listen to how you use the room, and measure walls, openings, outlets and plumbing locations.

2. 2

   Drawings and 3D model

   You go over the plans and a rendered model, marking changes until every wall reads right.

3. 3

   Wood selection and samples

   Physical samples of wood, door profile and finish let you judge each choice under your own lighting.

4. 4

   Shop build

   Boxes, frames, doors and drawers are milled, joined and finished on Lewis Ave.

5. 5

   Installation

   We set, level, scribe and fasten the cabinets, add trim, and adjust every door and drawer.

6. 6

   Countertops and trades

   Once cabinets are set, the stone fabricator makes templates for the tops and licensed trades finish their hookups.

Florida's DBPR licenses those contractors under Chapter 489, Florida Statutes, and the Florida Building Code governs their work. Longboat Key, Venice and North Port run their own building departments. In a FEMA flood zone, the NFIP substantial-improvement rule can require a house to meet current flood standards once improvement costs reach half its market value.

What sets the price of custom cabinetry in Sarasota?

We price each job from its drawings, so the number reflects your room rather than a catalog line. The biggest drivers are:

• Linear footage of cabinetry and the number of doors and drawers
• Wood species, since walnut and exotics cost more than paint-grade maple
• Door style, with inset doors taking the most fitting time
• Finish system: stain, clear coat, paint or a glazed treatment
• Interior fittings such as roll-outs, organizers and lighting channels
• Site conditions, including out-of-level floors, high ceilings and condo access

Two local variables add time: condo association approvals, elevator bookings and short work hours on the keys and downtown, and extra scribing in older block homes with bowed walls. Your written estimate ties each to the drawings, so a change order shows what moved.

Custom cabinet cost in Sarasota explores each factor further.

Commercial cabinetry and millwork cabinetry for businesses

Our shop also builds for offices, medical and professional suites, restaurants, retail counters and break rooms. Commercial work asks more of cabinetry: heavier daily use, cleaning chemicals, and fixed dates tied to an opening. We plan doors and tops for traffic, choose finishes that tolerate frequent wiping, and coordinate our schedule with the general contractor running the build-out.

Reception desks, display walls and storage runs often blend into architectural woodwork, so we pair cabinetry with paneling and trim from our finish carpentry and millwork work when the space calls for it.

Caring for wood cabinetry in a humid climate

Good wood cabinets need little more than a soft cloth, a mild cleaner and steady indoor humidity. Wipe spills at the sink edge promptly, and leave the AC on while a seasonal home sits empty.

Our guide to caring for wood cabinets in Florida covers cleaning products, touch-ups and humidity targets.